COBRA 18M with Internal LI-PO rechargable battery and armored case
Warning: Last items in stock!
Availability date: 02/29/2016
COBRA 18M is now rechargable! In fact, this version contain a Li-Po battery pack and 18M is 100% rechargable.
You can racharge your 18M, simply connecting the charger at the front of it.
The 18M is a compact and rugged 18-cue firing module that functions universally with the 18R and 18R2 hand-held remotes and is perfect for both indoor and harsh outdoor environments. Each cue boasts 18V at 6A firing up to 10 series-wired e-matches, or 4 parallel-wired e-matches or Talon brand igniter clips per cue.
Each firing module can be set to one of 100 channels by simply pressing the + and - buttons on the module. Then, using the 18R or 18R2 hand-held remote channel controls, you can fire any modules on the same channel. You can fire unlimited modules at the exact same time by setting them to the same channel.
Simply press CH+ or CH- on the 18M to set any module to a channel between 00 and 99. Then, by changing the channel on the 18R or 18R2 hand-held remote, you can fire any module set to the same channel.
You can also set multiple modules on the same channel to have them fire at the exact same time. This is common for multi-position fronts, firing around a stadium, rooftop shoots, and other simultaneous effects separated by large distances.
The 18M uses an 14.8V Lipo Battery.
The 18M also has a power conserving sleep mode. When powering off the 18R or 18R2 remote, the 18M will automatically fall asleep and conserve power for up to 48 hours. This allows you to place and arm your modules into position hours before the show begins. Then, when turning on your 18R or 18R2 remote, the module wakes up and is ready to fire.
It is not uncommon for customers to use the same recharge for 10-15+ shows.
At COBRA, we believe safety and reliability are the most important features of any firing system. With that in mind, every COBRA system incorporates the below collection of technological and usability based features. This ensures safe and reliable functionality every time you use the system.
IEEE® Unique Network MAC Addresses - Every COBRA remote contains a fully unique network MAC address. This address is programmed onto the unit at the time of production and contains 16 x 0-F base-16 values. For example, 00.1C.2C.00.00.C0.00.01.By syncing a firing module to a remote, the remote's network MAC address is saved and remembered on the firing module, even after power-on and power-off. Once saved, the firing module will ONLY respond to the remote containing this unique MAC address. This prevents any other remotes from firing your system. In addition, any time a firing module is synced to a different remote, the previous MAC address is overwritten, thereby ensuring the firing module only responds to the last remote to which it was synced.
2.4GHz tranceiver modules - The Cobra 18M uses a 2.4GHz transceiver module manufactured by Synapse, a US company that both develops and manufactures its SNAP line of IEEE 802.15.4 radio modules and transceiver ICs.The same transceiver and software development platform is used successfully not only by COBRA, but also in a variety of safety-critical industrial wireless applications, including medical monitoring systems and airport lighting controls.
Redundant, solid-state, self-testing MOSFETs - The COBRA 18M uses redundant solid-state firing FETs on both the high and low side of each firing cue. This ensures that no power is supplied to the cue unless the firing module is both armed, in fire mode and is actively firing a cue. The redundant FETs provide protection against unintentional electro-static discharge (ESD) and serve to automatically test for damaged or shorted FETs upon system start-up. If detected, the system will automatically disable itself and will not operate.
NFPA compliant user-design - The COBRA system adheres to National Fire Protection Association (NFPA) chapter 9.2 requirements including a key-operated switch, multiple actions to arm and fire, and minimum current requirements when performing continuity tests.
Contains FCC, CE and IC certified RF Module - The 18M contains the Synpase 802.15.4 2.4GHz RF transceiver module./p>
The 18M is enclosed in 2.5mm thick high-strength ABS plastic and shielded by a highly thermal and impact resistant black armored plating on the top side. The clear design minimizes all entry of air, moisture, and dust into the electronic housing by eliminating the need for cut-outs and micro-gaps in the enclosure. Polyurethane-coated fire-retardant silicon keypads have custom walls that push up against the top-enclosure to protect against moisture and dust.
60% More Battery Life - Fits perfectly in the existing battery compartment, the battery pack lasts 60% longer than the existing 9V batteries. This is accomplished with 900mAh vs. the traditional 550mAh of a 9V battery.
Easy to Charge - A charge port and charge indicator exists on the top of the module for simple charging. If you own armored cases, a new face plate supports charging while the 18M is still in the armored case. Use our single charger or charge up to 5 modules at once with our 5-module charger option.
External 12-24V DC Input - Optional rugged external binding posts support external 12 and 24V DC input. For permanent installations, we offer a custom 110/220V A/C to 24V D/C converter. Use the internal LiPo battery pack together with the A/C input to act as a real-time power backup.
Increased Amperage - The existing replaceable 9V batteries produce a peak current of 3 Amps. Using the LiPo battery pack, this increases to 6 Amps. Using the external power input, we can produce up to 9 Amps of peak current. This will support firing up to 8 and 12 e-match / talons respectively, in addition to also supporting the firing of high current devices such as confetti cannons, flame projectors, and cryo jets.
Cold Weather Performance - Fire extreme cold shows with confidence with improved cold weather performance down to -20F / -29C.
Dual Protection Circuits for LiPo Safety - COBRA incorporates dual overcharge, undercharge, and over voltage protection circuits. The first protection circuit is built into the 18M adapter board installed with the upgrade. The second protection circuit is built into the battery itself. This means if one of the protection circuits fails, the other acts as a backup. While we don't expect any failures, feel confident that we have designed both the battery and charge circuitry with the highest level of safety and protection in mind.
No customer reviews for the moment.